• Engineered with Strict Industry Standards
• Extensively Tested Under Various Driving Conditions
• Factory Safety Limiters Retained
• Engine Temperature Protection (Rev Limit based on Engine Coolant Temperature)
• Optimized Responsiveness and Drivability
• Optimized Smoothness and Driving Comfort
• Power Delivery Perfectly Optimized Throughout the Power Band
• Improved Fuel Efficiency
• Ignition Timing Precisely Calibrated for Higher Octane Fuel
• Speed Governor Removed
• Includes all Stage 1+ tune variants and all lower software stages.

• Carbon Fiber Intake System With Air Duct For 1.8/2.0 TSI Gen3 MQB
• MQB Turbo Inlet Elbow
• *Must use Unitronic Intake, Air Duct and Turbo Inlet to achieve published power figures and to ensure maximum turbocharger longevity. Unitronic cannot guarantee engine performance if using third party hardware.

Stage 2

• Engineered with Strict Industry Standards
• Extensively Tested Under Various Driving Conditions
• Factory Safety Limiters Retained
• Engine Temperature Protection (Rev Limit based on Engine Coolant Temperature)
• Optimized Responsiveness and Drivability
• Optimized Smoothness and Driving Comfort
• Power Delivery Perfectly Optimized Throughout the Power Band
• Improved Fuel Efficiency
• Ignition Timing Precisely Calibrated for Higher Octane Fuel
• Speed Governor Removed
• Includes all Stage 2 tune variants and all lower software stages.
• Exhaust Overrun/Crackle Enabled with Stage 2 and up. Requires UniConnect+ cable. Subject to availability.

• Unitronic Performance Downpipe 2.0 TSI MQB EA888.3 AWD

• Carbon Fiber Intake System With Air Duct For 1.8/2.0 TSI Gen3 MQB
• Charge Pipe Upgrade Kit For MQB
• Intercooler Upgrade Kit for 1.8 and 2.0 TSI Gen3 MQB and 8Y S3 by Unitronic
• MQB Turbo Inlet Elbow
• *Must use Unitronic Intake, Air Duct and Turbo Inlet to achieve published power figures and to ensure maximum turbocharger longevity. Unitronic cannot guarantee engine performance if using third party hardware.

• End-User Programmable with UniCONNECT+
  Flash your TCU from the comfort of your own home or garage. Within minutes (approximately 70-seconds to be exact on this platform), you'll be enjoying an entirely transformed driving experience.
  
  
• Optimized D & Sport Modes
  D-mode is optimized for everyday daily driving and economy, while S-mode is optimized for faster acceleration.
  
  
• Dual Setpoint Adjustable Launch Control
  Unitronic has adjusted the launch control RPM setpoints to allow for quicker acceleration off the launch control. Dual-stage launch control allows users to choose between two different launch control RPM setpoints based on the current conditions observed. (surface conditions, tires, etc.) Launch Control Setpoint 1 is activated at 100% pedal position, without engaging the kick-down switch. Launch Control Setpoint 2 is activated at "110%" pedal position. (100% pedal position with the kick-down switch engaged)
  
  
• Quicker Gear Shifts
  Unitronic's TCU Performance Software calibration enhances the gear shift speeds making them up to 70% quicker.
  
  
• Gear Display Enabled in D and S Mode
  Gear Display is enabled, allowing the driver to see the current gear in both D- and S-mode on the Virtual Cockpit / MFD.(D1, D2, etc. & S1, S2, S3, etc.

Stage 2 DSG

Features

 

Stage 2 DSG Software Precisely Engineered to run combined with a Unitronic Stage 2 or Stage 2+ performance software.

• End-User Programmable with UniCONNECT+
  Flash your TCU from the comfort of your own home or garage. Within minutes (approximately 70-seconds to be exact on this platform), you'll be enjoying an entirely transformed driving experience.
  
  
• Optimized D & Sport Modes
  D-mode is optimized for everyday daily driving and economy, while S-mode is optimized for faster acceleration.
  
  
• Dual Setpoint Adjustable Launch Control
  Unitronic has adjusted the launch control RPM setpoints to allow for quicker acceleration off the launch control. Dual-stage launch control allows users to choose between two different launch control RPM setpoints based on the current conditions observed. (surface conditions, tires, etc.) Launch Control Setpoint 1 is activated at 100% pedal position, without engaging the kick-down switch. Launch Control Setpoint 2 is activated at "110%" pedal position. (100% pedal position with the kick-down switch engaged)
  
  
• Quicker Gear Shifts
  Unitronic's TCU Performance Software calibration enhances the gear shift speeds making them up to 70% quicker.
  
  
• Gear Display Enabled in D and S Mode
  Gear Display is enabled, allowing the driver to see the current gear in both D- and S-mode on the Virtual Cockpit / MFD.(D1, D2, etc. & S1, S2, S3, etc.)
  
  
• Raised Torque Limiters
  Unitronic's Stage 2 TCU Performance Software calibrations increase TCU torque limiters to allow for an increased output and has been developed alongside Unitronic's Stage 2 ECU Performance Software for the ultimate overall experience.
  
  
• Increased Clutch Clamping Pressure
  Unitronic's Stage 2 TCU Performance Software calibrations increase clutch clamping pressure and has been developed in conjunction with and alongside Unitronic's Stage 2 ECU Performance Software, supporting the increase in engine torque output and ensuring that the clutches properly grip allowing for the higher output to be sustained.
  
  
• Full Staged Software Suite
  Includes all Stage 2 tune variants and all lower software stages as well.

 

Unitronic's UniCONNECT+

 

Description

 

UniCONNECT+ is a Programming and Diagnostic Interface which gives users the freedom to reflash their Engine Control Unit (ECU) or Transmission Control Unit (TCU) from the comfort of their own garage. With the ability to upgrade the Unitronic Performance Software, flash back to stock, and also perform diagnostics, UniCONNECT+ is a complete end-user programming and diagnostic interface that provides control over your vehicle.

 

 

Availability

 

UniCONNECT+ is available for purchase through our Authorized Dealer Network and directly from Unitronic. UniCONNECT+ is compatible with most of 2006 and up vehicles.*

 

 

Simple Installation

 

UniCONNECT+ gives you the freedom to effortlessly install your Unitronic Performance ECU and DSG Software from the comfort of your own home or garage.*

Unitronic recommends the use of these battery chargers to ensure, uninterrupted, trouble-free, flashing at home!

OptiMate 7 SELECT

OptiMate 6 SELECT

 

 

Change Software Maps

 

Quickly and Easily re-flash your ECU with Performance Software maps designed and specifically calibrated to suite the hardware and fuel modifications or fuel grade used.

 

 

Data Logging

 

Gathering high resolution data is made easy with Unitronic’s pre-configured channel loadouts for fast and effortless troubleshooting and data logging.**

 

 

Simple back to factory restoration

 

UniCONNECT+ makes it painless to revert your ECU back to it’s stock calibration within minutes.*

 

 

Advanced Settings

 

Enable optional advanced settings such as Launch Control or No Lift Shifting within minutes. Enable Gear display in MFG for DSG Software owners.*

 

 

Technical Specifications

 

Minimum System Requirements:
Operating System: Microsoft Windows 10 or 11
Internet Explorer 11
Screen Resolution: 1024x768
Processor: 1.5 GHz or higher
Memory (RAM): 4GB or more

For optimal application performance:
Operating System: Microsoft Windows 11
Internet Explorer 11 or newer
Screen Resolution: 1024x768
Processor: 2.0 GHz or higher
Memory (RAM): 8GB or more

Internet access is required.

 

 

*Some exclusions apply. UniCONNECT+ cables are VIN-locked and can only be used on one vehicle. Only available for select engines. Contact US for more information.
**Feature in development.